8-34mm Automatic Handheld Rebar Tier Tool Building Tying Machine Strapping Tool

  
8-34mm Automatic Handheld Rebar Tier Tool Building Tying Machine Strapping Tool. Tool box size: 42cm (16.54inch) 30cm (11.81inch) 10cm (3.94inch). Battery Charging Time: 1.5 hours full filling. Tying Wire Diameter: 0.8mm. Tying Wire Length: more than 110 m. Applicable Scope Of Steel Strapping: 8mm - 34mm. Knot Wire Length: 300 - 500mm. Knot Number Per Charge: 1500 times. Knot The Required Time: 0.8 seconds at a time. Machine Size: 275 mm 65 mm 240 mm / 10.83''x2.56''x9.45''appr. Brand New and high quality. Compact size, lightweight, easy to grab. It can save 3-5 times than man power by hand. Rebar Tier is a hand held machine used to pack rebars quickly. It is a miniature motor tool has the trait of safety and credibility. Used for building market, including civil building, floor pipe, heating floor mesh, steel bar, etc. Reasonable structure, advanced craft, simple and convenient operation, high efficiency and convenient maintenance. In the state of start-up, press the locking plate of the opening wire plate, open the plate cover. Take out the tying wire, tear the packaging film, pull straight wire head about 10 cm, load into the binding machine in the clockwise direction, the wire head into the guide tap tube. Note: Clench the wire plate when tear the packaging film, do not let the wire loose. If the wire is free to disperse, it will lead to the spread of the wire stuck in the wire plate. Insert the head of the wire guide into the tap pipe until it is resisted. Cover the plate and fasten the locking piece. Pinch the wire forward with two fingers, press and hold the switch and send the wire out. If you want to take out the wire plate when finished, press and hold the locking piece, open the wire plate cover plate, holding the wire tray to the side and pull out. The rebar tirer's jaws are stuck to the intersection of the steel bars, and the steel bars are hooked at 45 degree angles. Note: There can be no barrier between the mouth of the jaws and the wire.

Press the start switch, the rebar tirer machine carries on the work (spins, hinges tightly, cuts off). Note: Press one button at a time, do not probe the jaws at work.

When automatic completion, the jaw from the steel bar intersection and then pull back, complete the process and prepare for the next binding. When the binding process is not completed, do not unplug the machine in advance, otherwise it will cause the bundling of the goods tied skidding.

In use, the left tilt 45 degrees after banding, the next time the banding into a right tilt 45 degrees banding, left and right alternately banding. When the machine is about to tighten, the machine will appear slightly shaking, while holding the hand of the machine not too tight, you can relax properly. Clean the machine regularly, keep the wire mouth clean.

This product can not be placed randomly, so as not to cause damage to parts. Batteries must not be placed together with other metal objects to avoid short circuit.

Non-professional do not disassemble the machine arbitrarily, lest cause damage. When you encounter an unresolved failure, please give it to the professional repair. 1X Tying Wire in the machine (Tying Wire Standard: About 0.8 mm x 110 m/roll). Please allow 1-3cm error due to manual measurement and make sure you do not mind before ordering. Please understand that colors may exist chromatic aberration as the different placement of pictures.

Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal.

We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately.

If it's non-workdays, please kindly be patient and wait till Monday. Easy installation, Convenient Use, Easy Operation.

Great Durability, Exquisite Appearance, High-quality. Do not send to Brazil. Compact Design and Beautiful Appearance.

1.5 hours full filling. Applicable Scope Of Steel Strapping.

0.8 seconds at a time. 275 mm 65 mm 240 mm / 10.83''x2.56''x9.45''ap.

42cm (16.54inch) 30cm (11.81inch) 10cm (3.94inch).